Get to Know Your Integra Camino ICP Battery

Before we start replacing it, let's first understand the battery used in the Integra Camino ICP monitor. This device uses a 14.4V special lithium battery. Just like a pacemaker requires a specific power source, this type of medical equipment has strict requirements for the battery.

Safety Tips: This is not an ordinary battery replacement

Battery replacement for medical equipment is different from replacing the battery for the remote control. We must put safety first:

Four major prohibitions:

1.  It is forbidden to use hair dryers, heat guns, etc., to heat above 80℃. (Exceeding 80℃ may cause explosion)
2. It is forbidden to disassemble the battery. (There is a high-voltage circuit inside)
3. It is forbidden to expose it to flames.
4.  It is forbidden to short-circuit the battery, otherwise, it may burn, explode, leak, or overheat and cause personal injury.

Professional Tips: It is recommended to wear insulating gloves when replacing, just like electricians do, which are both anti-static and safe.

Battery replacement steps

Step 1: Prepare

Confirm the device status:

1. Press and hold the power button for 3 seconds to turn off the device
   
2. Unplug all cables (including power cord, data cable, etc.)
   
3. Observe the screen to ensure that the power is completely off

Prepare tools and site:

1. Cross screwdriver (magnetic head is recommended to prevent screws from falling)
   
2. Clean and flat workbench
   
3. Antistatic mat (optional, but very professional)

Step 2: Remove the battery cover

Device positioning:

1. Flip the monitor 180 degrees with the handle facing down
   
2. It is best to use a soft cloth to prevent scratching the device

Screw handling tips:

1. Use a screwdriver of appropriate size
   
2. Remove the screw by turning it counterclockwise
   
3. It is recommended to store the screws in a small container to avoid losing them

Step 3: Battery replacement

Remove the old battery:

1. Observe the battery buckle position
2. Usually, you need to press the buckle first and then slide it out
3. Pay attention to the direction of the connector removal

Install the new battery:

1. Key point: The arrow mark on the battery must face upwards
2. Align the connector before inserting, and avoid brute force

Step 4: Installation completed

Tips for screw reset:

1. Pre-tighten the screws by hand first
2. Tighten with a screwdriver with moderate force
3. Check if the battery cover fits perfectly

Device reset check:

1. Restore the device to the upright position
2. Shake gently and listen for any abnormal sounds

Battery Charging Guide

After the battery is installed, use the AC power adapter to charge the battery to full capacity. The specific steps are as follows:

First, turn off the monitor by pressing the power button on the front of the monitor.

Second, after turning off the monitor, keep it connected to the AC power supply for 5 hours. This operation can fully charge the battery.

Third, after 5 hours, press the power button to turn on the monitor.

Fourth, you can see on the touch screen that there are four green stripes in the battery status bar, which means that the battery is fully charged.

How to handle a low battery alarm

The Integra Camino ICP has high voltage limit alarm and technical alarm functions, which will automatically trigger the corresponding alarm when the device exceeds the high voltage limit or encounters technical problems. In addition, the device is equipped with a low battery alarm system, which is handled as follows:

Low battery alarm hierarchical handling

Battery remaining ≤ 15 minutes

1. The status bar will display the "low battery" prompt.
2. Handling measures: Connect AC power immediately; the warning will continue to display until the power is connected.

Battery remaining ≤ 5 minutes

1. A medium priority alarm is triggered, which is manifested as:

• An alarm tone with three pauses is emitted;
• The status bar displays "Low Battery" and the yellow battery symbol flashes.

1. Handling measures: The AC power supply must be connected immediately, and the alarm will automatically turn off after it is connected.
2. Warning: If the power supply is not connected in time, the device may shut down due to exhaustion.

Temporarily deactivate the low battery alarm.

Users can silence the alarm for 3 minutes by tapping the flashing alarm symbol on the screen. The alarm will reactivate if AC power is not connected within 3 minutes.

If this article still doesn't help your laptop battery, you can buy a new battery at  BatteryMall.com

If you want to learn more about batteries, please visit: BatteryMall.com/blogs/suppor